? semiconductor components industries, llc, 2016 july, 2016 ? rev. 4 1 publication order number: nlu3g17/d nlu3g17 triple non-inverting schmitt-trigger buffer the nlu3g17 minigate is an advanced high?speed cmos triple non?inverting schmitt?trigger buffer in ultra?small footprint. the nlu3g17 input and output structures provide protection when voltages up to 7.0 v are applied, regardless of the supply voltage. the nlu3g17 can be used to enhance noise immunity or to square up slowly changing waveforms. features ? high speed: t pd = 4.0 ns (typ) @ v cc = 5.0 v ? low power dissipation: i cc = 1 a (max) at t a = 25 c ? power down protection provided on inputs ? balanced propagation delays ? overvoltage tolerant (ovt) input and output pins ? ultra?small packages ? these are pb?free devices in a2 out y2 1 out y2 in a1 gnd out y1 in a2 figure 1. pinout (top view) figure 2. logic symbol v cc in a1 out y1 1 1 2 3 4 8 7 6 5 out y3 in a3 in a3 out y3 1 function table l h ay l h pin assignment 1 2 3in a2 in a1 out y3 4 5 out y2 gnd 6 in a3 7 out y1 8v cc marking diagrams www. onsemi.com see detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ordering information udfn8 case 517aj 1 8 uz, d or lx = specific device code m = date code = pb?free package uzm udfn8 1.45 x 1.0 case 517bz udfn8 1.6 x 1.0 case 517by udfn8 1.95 x 1.0 case 517ca x m 1 x m 1 x m 1
nlu3g17 www. onsemi.com 2 maximum ratings symbol parameter value unit v cc dc supply voltage ?0.5 to +7.0 v v in dc input voltage ?0.5 to +7.0 v v out dc output voltage ?0.5 to +7.0 v i ik dc input diode current v in < gnd ?20 ma i ok dc output diode current v out < gnd 20 ma i o dc output source/sink current 12.5 ma i cc dc supply current per supply pin 25 ma i gnd dc ground current per ground pin 25 ma t stg storage temperature range ?65 to +150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias 150 c msl moisture sensitivity level 1 f r flammability rating oxygen index: 28 to 34 ul 94 v?0 @ 0.125 in i latchup latchup performance above v cc and below gnd at 125 c (note 2) 500 ma stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. measured with minimum pad spacing on an fr4 board, using 10 mm?by?1 inch, 2 ounce copper trace no air flow. 2. tested to eia / jesd78. recommended operating conditions symbol parameter min max unit v cc positive dc supply voltage 1.65 5.5 v v in digital input voltage 0 5.5 v v out output voltage 0 5.5 v t a operating free?air temperature ?55 +125 c t/ v input transition rise or fall rate v cc = 3.3 v 0.3 v v cc = 5.0 v 0.5 v 0 0 no limit no limit ns/v
nlu3g17 www. onsemi.com 3 dc electrical characteristics symbol parameter conditions v cc (v) t a = 25 c t a = +85 c t a = ?55 c to +125 c unit min typ max min max min max v t+ positive threshold voltage 3.0 4.5 5.5 1.85 2.86 3.50 2.0 3.0 3.6 2.2 3.15 3.85 2.2 3.15 3.85 2.2 3.15 3.85 v v t? negative threshold voltage 3.0 4.5 5.5 0.9 1.35 1.65 1.5 2.3 2.9 1.65 2.46 3.05 0.9 1.35 1.65 0.9 1.35 1.65 v v h hysteresis voltage 3.0 4.5 5.5 0.30 0.40 0.50 0.57 0.67 0.74 1.20 1.40 1.60 0.30 0.40 0.50 1.20 1.40 1.60 0.30 0.40 0.50 1.20 1.40 1.60 v v oh minimum high?level output voltage v in v t+max i oh = ?50 a 2.0 3.0 4.5 1.9 2.9 4.4 2.0 3.0 4.5 1.9 2.9 4.4 1.9 2.9 4.4 v v in v t+max i oh = ?4 ma i oh = ?8 ma 3.0 4.5 2.58 3.94 2.48 3.80 2.34 3.66 v ol maximum low?level output voltage v in v t?min i ol = 50 a 2.0 3.0 4.5 0 0 0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 v v in v t?min i ol = 4 ma i ol = 8 ma 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 i in input leakage current 0 v in 5.5 v 0 to 5.5 0.1 1.0 1.0 a i cc quiescent supply current 0 v in v cc 5.5 1.0 10 40 a ac electrical characteristics (input t r = t f = 3.0 ns) symbol parameter v cc (v) test condition t a = 25 c t a = +85 c t a = ?55 c to +125 c unit min typ max min max min max t plh , t phl propagation delay, input a to output y 3.0 to 3.6 c l = 15 pf 7.0 12.8 1.0 15 1.0 17 ns c l = 50 pf 8.5 16.3 1.0 18.5 1.0 20.5 4.5 to 5.5 c l = 15 pf 4.0 8.6 1.0 10 1.0 11.5 c l = 50 pf 5.5 10.6 1.0 12 1.0 13.5 c in input capacitance 5.0 10 10 10 pf c pd power dissipation capacitance (note 3) 5.0 7.0 pf 3. c pd is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumpt ion without load. average operating current can be obtained by the equation i cc(opr) = c pd ? v cc ? f in + i cc . c pd is used to determine the no?load dynamic power consumption: p d = c pd ? v cc 2 ? f in + i cc ? v cc.
nlu3g17 www. onsemi.com 4 figure 3. switching waveforms figure 4. test circuit a 1?mhz square input wave is recommended for propagation delay tests. c l input output r l v cc gnd 50% 50% v cc a or b y t phl t plh figure 5. typical schmitt?trigger applications v h v in v out v cc v t+ v t? gnd v oh v ol v h v in v out v cc v t+ v t? gnd v oh v ol (a) a schmitt?trigger squares up inputs with slow rise and fall times (b) a schmitt?trigger offers maximum noise immunity ordering information device package shipping ? nlu3g17mutag udfn8 (pb?free) 3000 / tape & reel nlu3g17dmutcg udfn8, 1.95 x 1.0, 0.5p (pb?free) 3000 / tape & reel nlu3g17emutcg udfn8, 1.6 x 1.0, 0.4p (pb?free) 3000 / tape & reel NLU3G17FMUTCG udfn8, 1.45 x 1.0, 0.35p (pb?free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
nlu3g17 www. onsemi.com 5 package dimensions udfn8 1.6x1.0, 0.4p case 517by issue o soldering footprint* recommended dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.13 ref b 0.15 0.25 d 1.60 bsc e 1.00 bsc e 0.40 bsc l 0.25 0.35 l1 0.30 0.40 a b e d 0.10 c pin one reference top view 0.10 c a a1 0.05 c 0.05 c c seating plane side view 2x 2x a3 bottom view b e 8x l 7x l1 1 4 5 8 e/2 0.10 b 0.05 a c c note 3 m m dimensions: millimeters 0.26 7x 0.49 8x 1.24 0.53 pitch 0.40 1 pkg outline
nlu3g17 www. onsemi.com 6 package dimensions udfn8 1.45x1.0, 0.35p case 517bz issue o soldering footprint* recommended dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.13 ref b 0.15 0.25 d 1.45 bsc e 1.00 bsc e 0.35 bsc l 0.25 0.35 l1 0.30 0.40 a b e d 0.10 c pin one reference top view 0.10 c a a1 0.05 c 0.05 c c seating plane side view 2x 2x a3 bottom view b e 8x l 7x l1 1 4 5 8 e/2 dimensions: millimeters 0.22 7x 0.48 8x 1.18 0.53 pitch 0.35 1 pkg outline 0.10 b 0.05 a c c note 3 m m
nlu3g17 www. onsemi.com 7 package dimensions udfn8 1.95x1.0, 0.5p case 517ca issue o soldering footprint* recommended dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.13 ref b 0.15 0.25 d 1.95 bsc e 1.00 bsc e 0.50 bsc l 0.25 0.35 l1 0.30 0.40 a b e d 0.10 c pin one reference top view 0.10 c a a1 0.05 c 0.05 c c seating plane side view 2x 2x a3 bottom view b e 8x l 7x l1 1 4 5 8 e/2 dimensions: millimeters 0.30 7x 0.49 8x 1.24 0.54 pitch 0.50 1 pkg outline 0.10 b 0.05 a c c note 3 m m
nlu3g17 www. onsemi.com 8 package dimensions udfn8 1.8x1.2, 0.4p case 517aj issue o notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.30 mm from terminal tip. 4. mold flash allowed on terminals along edge of package. flash may not exceed 0.03 onto bottom surface of terminals. 5. detail a shows optional construction for terminals. a b e d bottom view b e 8x b a c c note 3 0.10 c pin one reference top view 0.10 c a a1 (a3) 0.05 c 0.05 c c seating plane side view l 8x 1 4 5 8 dim min max millimeters a 0.45 0.55 a1 0.00 0.05 a3 0.127 ref b 0.15 0.25 d 1.80 bsc e 1.20 bsc e 0.40 bsc l 0.45 0.55 e/2 b2 0.30 ref l1 0.00 0.03 l2 0.40 ref detail a (l2) (b2) note 5 l1 detail a m 0.10 m 0.05 0.22 0.32 8x 1.50 0.40 pitch 0.66 dimensions: millimeters mounting footprint 7x 1 soldermask defined *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 nlu3g17/d minigate is a trademark of semiconductor components industries, llc (scillc). literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative on semiconductor and are trademarks of semiconductor components industries, llc dba on semiconductor or its subsidiaries i n the united states and/or other countries. on semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property . a listing of on semiconductor?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf . on semiconductor reserves the right to make changes without further notice to any products herein. on semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does o n semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. buyer is responsible for its products and applications using on semiconductor products, including compliance with all laws, reg ulations and safety requirements or standards, regardless of any support or applications information provided by on semiconductor. ?typical? parameters which may be provided in on semiconductor data sheets and/or specifications can and do vary in dif ferent applications and actual performance may vary over time. all operating parameters, including ?typic als? must be validated for each customer application by customer?s technical experts. on semiconductor does not convey any license under its patent rights nor the right s of others. on semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any fda class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. should buyer purchase or use on semicondu ctor products for any such unintended or unauthorized application, buyer shall indemnify and hold on semiconductor and its officers, employees, subsidiaries, affiliates, and distrib utors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that on semiconductor was negligent regarding the design or manufacture of the part. on semiconductor is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner.
|
